Items with Index Term: plastic

Adefila, A; Abuzeinab, A; Whitehead, T and Oyinlola, M (2020) Bottle house: Utilising appreciative inquiry to develop a user acceptance model. Built Environment Project and Asset Management, 10(4), pp. 567-583. ISSN 2044-124X

Aderinlewo, O and Alade, G A (2014) Reliability-based analysis and design of steel frames with different supports. Journal of Engineering, Design and Technology, 12(1), pp. 39-52. ISSN 1726-0531

Ali Khan, M S; Suresh, A and Ramaiah, N S (2016) Numerical study of magnetic circuit response in magneto-rheological damper. Journal of Engineering, Design and Technology, 14(1), pp. 196-210.

Alqahtani, F K; Alkhaldi, M; Alsaqer, T; Abotaleb, I S; Mohamed, A G and Dirar, S (2022) A comparative assessment of advanced construction systems incorporating green concrete. Journal of Construction Engineering and Management, 148(9): 04022083, ISSN 0733-9364

Andersson, R and Buser, M (2020) On the road to nowhere? The challenges of aligning construction and demolition waste practices with circular economy. In: Scott, L and Neilson, C J (eds.) Proceedings of 36th Annual ARCOM Conference, 7-8 September 2020, Online Event, UK.

Arpaci, E Y G; Akbulut, D E and Yildiz, O (2024) Enhancing water resistance of earthen buildings by using admixture materials. Architectural Engineering and Design Management, 20(2), pp. 320-336. ISSN 1745-2007

Aviram Traubita, A (2009) Structural response and cost characterization of bridge construction using seismic performance enhancement strategies. PhD thesis, University of California, Berkeley, USA.

Babrauskas, V; Lucas, D; Eisenberg, D; Singla, V; Dedeo, M and Blum, A (2012) Flame retardants in building insulation: A case for re-evaluating building codes. Building Research & Information, 40(6), pp. 738-755. ISSN 0961-3218

Bakhtiyari, S; Taghi Akbari, L and Jamali Ashtiani, M (2017) An investigation on fire hazard and smoke toxicity of epoxy FRP composites. International Journal of Disaster Resilience in the Built Environment, 8(3), pp. 230-237. ISSN 1759-5916

Banfill, P F G (1983) The effect of admixtures on the rheology of fresh concrete. Construction Papers, 2(1), pp. 63-77. ISSN 0144-8587

Blindheim, J; Elverum, C W; Welo, T and Steinert, M (2020) Concept evaluation in new product development: A set-based method utilizing rapid prototyping and physical modelling. Journal of Engineering, Design and Technology, 18(5), pp. 1139-1151. ISSN 1726-0531

Burford, N K and Smith, F W (1999) Developing a new military shelter system: A technical study in advanced materials and structures. Building Research & Information, 27(2), pp. 64-83. ISSN 0961-3218

Chen, Y; Fang, Q and Lan, Y (2025) Development of a modular assembling, suspended, and sliding scaffold. Journal of Construction Engineering and Management, 151(9): 04025131, ISSN 0733-9364

Choi, B (2003) Topics in risk-based design and performance evaluation of structures. PhD thesis, North Carolina State University, USA.

Damdelen, O and Tansu, A (2022) Influence of recycled plastic on the thermal transmittance and sustainable assessment of concrete mixes. Journal of Construction Engineering and Management, 148(12): 04022135, ISSN 0733-9364

Fan, Y and Kokko, E (1997) Three-dimensional gaseous transfer within cellular plastic insulation and its consequences. Building Research & Information, 25(1), pp. 25-35. ISSN 0961-3218

Friedrich, D (2022) Consumer and expert behaviour towards biobased wood-polymer building products: A comparative multi-factorial study according to theory of planned behaviour. Architectural Engineering and Design Management, 18(1), pp. 73-92. ISSN 1745-2007

Gai, X (2012) Fibre reinforced polymer (FRP) stay-in-place (SIP) participating formwork for new construction. PhD thesis, University of Bath, UK.

Gambo, N and Musonda, I (2021) Effect of the fourth industrial revolution on road transport asset management practice in Nigeria. Journal of Construction in Developing Countries, 26(1), pp. 19-43. ISSN 1823-6499

Ganguly, I (2008) Modeling alternatives and visualization of product adoption and usage in the residential construction industry. PhD thesis, University of Washington, USA.

George, M and Sekpe, V (2010) Inspection of insulated concrete form walls using ground penetrating radar. International Journal of Construction Education and Research, 6(4), pp. 303-317. ISSN 1557-8771

Ghannoum, M; Assaad, J; Daaboul, M and El-Mir, A (2025) Deterministic and stochastic finite element modeling of reinforced concrete beams without stirrups containing plastic wastes. International Journal of Building Pathology and Adaptation, 43(4), pp. 614-632. ISSN 2398-4708

Hassan, M M and Gruber, S (2008) Simulation of concrete paving operations on Interstate-74. Journal of Construction Engineering and Management, 134(1), pp. 2-9. ISSN 0733-9364

Ibrahim, I.; Haj-Salem, N.; Ashour, A. G. and Alotaibi, E. B. (2026) Assessment of consumer behaviour towards recycled plastic products: Insights from the UAE. Construction Economics and Building, 26(2), ISSN 2204-9029

Imran, S A; Commuri, S; Barman, M; Zaman, M and Beainy, F (2017) Modeling the dynamics of asphalt-roller interaction during compaction. Journal of Construction Engineering and Management, 143(7): 04017015, ISSN 0733-9364

Jaafari, A (1977) Development and use of composite fibrous materials in the UK construction industry. PhD thesis, University of Surrey, UK.

Kalu, I E and Ogbonna, N J (2021) Investigation of environmental effect of stone quarrying activities on soil and water in Akpoha and Ishiagu communities of Ebonyi State, Nigeria. International Journal of Construction Management, 21(12), pp. 1185-1199. ISSN 1562-3599

Katz, J I (2014) Quantifying "cliffs" in design space. Journal of Engineering, Design and Technology, 12(3), pp. 374-388.

Kleemann, F; Lederer, J; Aschenbrenner, P; Rechberger, H and Fellner, J (2016) A method for determining buildings' material composition prior to demolition. Building Research & Information, 44(1), pp. 51-62. ISSN 0961-3218

Levis, James William (2013) A mathematical programming life-cycle assessment model for solid waste management decision making. PhD thesis, North Carolina State University, USA.

Li, Y.; Tai, S. and Tai, Z. (2024) Development of ANP-based greenness evaluation model of construction technologies in China. Journal of Engineering, Design and Technology, 24(2), pp. 602-630. ISSN 1726-0531

Li, Liancheng (2025) Towards sustainable recovery of waste plastics with the Australian construction industry: Transition scenarios and environmental impact evaluation. PhD thesis, University of Adelaide, Australia.

Liu, L and Wan, S (2024) Flexural bearing capacity of reinforced concrete beams reinforced with carbon fiber reinforced plastics strips and ultra-high performance concrete layers. International Journal of Building Pathology and Adaptation, 42(6), pp. 1126-1146. ISSN 2398-4708

Lucke, T and Arthur, S (2011) Plastic pipe pressures in siphonic roof drainage systems. Building Research & Information, 39(1), pp. 79-92. ISSN 0961-3218

Nabi, M A; El-Adaway, I H and Assaad, R H (2024) Modeling inflation transmission among different construction materials. Journal of Construction Engineering and Management, 150(5): 04024024, ISSN 0733-9364

Najafi, M (1993) Evaluation of a new microtunneling propulsion system. DEng thesis, Louisiana Tech University, USA.

Nilsson, S (2003) Durability of district heating pipes. PhD thesis, Chalmers Tekniska Hogskola, Sweden.

Olbina, S and Beliveau, Y (2009) Developing a transparent shading device as a daylighting system. Building Research & Information, 37(2), pp. 148-163. ISSN 0961-3218

Onitiri, M A and Adedayo, S M (2015) Compressive behaviour of polypropylene filled with iron ore tailings. Journal of Engineering, Design and Technology, 13(2), pp. 198-212.

Rosado, Lais Peixoto (2019) Life cycle assessment of construction and demolition waste management in a Brazilian watershed. PhD thesis, Universidade Estadual de Campinas, Brazil.

Ruhl, V R (1997) Computer-aided design and manufacturing of complex-shaped concrete formwork. DDes thesis, Harvard University, USA.

Saleem, M; Elshami, M M and Najjar, M (2017) Development, testing, and implementation strategy of a translucent concrete-based smart lane separator for increased traffic safety. Journal of Construction Engineering and Management, 143(5): 04016129, ISSN 0733-9364

Sanusi, K O and Oliver, G J (2009) Effects of grain size on mechanical properties of nanostructured copper alloy by severe plastic deformation (SPD) process. Journal of Engineering, Design and Technology, 7(3), pp. 335-341. ISSN 1726-0531

Sayed, Ahmed Yehia Abdel Aziz El (2025) Design of novel formwork system and development of numerical model for comparison between formwork systems. PhD thesis, The American University in Cairo, Egypt.

Shaofeng, L; Jincai, F; Pinghua, Z and Xiang, L (2018) Stability analysis of two parallel closely spaced tunnels based on convergence-confinement principle. Journal of Construction Engineering and Management, 144(6): 04018041, ISSN 0733-9364

Shuler, S and Nobe, M D (2007) Edge cracking in residential development hot mix asphalt pavements. International Journal of Construction Education and Research, 3(3), pp. 179-197. ISSN 1557-8771

Sinclair, C. and Alwan, Z. (2026) Adaptability of concrete blocks, reinforced with recycled plastics: Circular construction approach from the UK. International Journal of Building Pathology and Adaptation, 44(4), pp. 1030-1045. ISSN 2398-4708

Skibniewski, M J and Kassouf, P J (1990) Potential for application of plastic liner plates in tunnelling works. Construction Management and Economics, 8(1), pp. 3-11. ISSN 01446193

Somani, N; Singh, N and Gupta, N K (2021) Joining and characterization of ss-430 using microwave hybrid heating technique. Journal of Engineering, Design and Technology, 19(6), pp. 1344-1357. ISSN 1726-0531

Stewart, J; Minchin, R E; Jaselskis, E J; Dayal, V and Smith, G (2004) Potential construction applications for thermoset composite scrap material. Journal of Construction Engineering and Management, 130(2), pp. 199-205. ISSN 0733-9364

Stewart, J H (2024) The plastics crisis: Responsible recycling in civil engineering and infrastructure. PhD thesis, Mississippi State University, USA.

Teixeira Brasil, Jose Artur (2025) A digital twin framework for monitoring, modeling, and forecasting the performance of permeable pavement systems. PhD thesis, The University of Texas at San Antonio, USA.

Tyvand, J and Blachly, A T (1986) Foamed plastic absorbs staged post-tensioning deflections. Journal of Construction Engineering and Management, 112(4), pp. 582-587. ISSN 0733-9364

Ugwu, O O; Arop, J B; Nwoji, C U and Osadebe, N N (2013) Nanotechnology as a preventive engineering solution to highway infrastructure failures. Journal of Construction Engineering and Management, 139(8), pp. 987-993. ISSN 0733-9364

Uzuegbunam, F O; Isiofia, L A and Ibem, E O (2024) Assessment of susceptibility of buildings with different façade finishes to microbial decay in the hot-humid tropical environment of enugu, southeast Nigeria. International Journal of Building Pathology and Adaptation, 42(6), pp. 1106-1125. ISSN 2398-4708

Xu, Z; Guo, X; Zhao, Y and Liu, X (2023) Performance of CFRP-bolted timber joints with slotted-in corrugated steel plates. Journal of Construction Engineering and Management, 149(12): 04023134, ISSN 0733-9364

Yang, X; Wang, S; Jiang, Y; Wang, L; Li, P and Wang, S (2025) Theoretical and experimental analysis of stress variations in precast concrete segment linings during double-shield TBM excavation of subway tunnels. Journal of Construction Engineering and Management, 151(6): 04025040, ISSN 0733-9364

Zeinali Kalkhoran, A; Platt, L S; Iovine, N; Brown, S and Pollitt, B (2025) An agent-based modeling approach for infection prevention predesign: simulating the spread of pathogens between humans and the environment in an Intensive Care Unit. Architectural Engineering and Design Management, 21(4), pp. 746-767. ISSN 1745-2007

Zhang, K; Li, D; Shen, X; Hou, W; Li, Y and Xue, X (2023) Research on strengthening stone arch bridge with CFRP rebars. International Journal of Building Pathology and Adaptation, 41(5), pp. 1014-1028. ISSN 23984708